News

• 

  Suitable Conditions for Machining Titanium Parts

  Round insert milling cutters are suitable for milling titanium because their leading angles can be varied as appropriate. As long as these milling cutters are equipped with special inserts and the correct cutting parameters are applied, stab....

  TAG: Titanium Alloys Titanium Processing CNC machining Lathe processing Turning Milling machining Shaft machining Material Metal Products Manufacturer Stainless steel processing Metal stamping Stamping die 

  Read more

• 

  Causes of poor machinability of titanium alloy

  Material machinability is often measured by the cutting speed allowed for cutting a material with a certain tool durability. Usually T = 60 min, then vT is written as v60. If the v60 used for cutting carbon steel in cemented carbide turning....

  TAG: Titanium Alloys Titanium Processing CNC machining Lathe processing Turning Milling machining Shaft machining Material Metal Products Manufacturer Bolt Screws Finishing Surface treatment Electroplating 

  Read more

• 

  Drilling of micro-holes in circuit board composites

  The specifications of printed circuit boards are complex and there are many types of products. The most widely used epoxy resin-based composite material in printed circuit boards is a micro hole (a small hole with a diameter of 0.6 mm or les....

  TAG: CNC machining Lathe processing Turning Milling machining Shaft machining Bolt Screws Fasteners Material Metal Products Manufacturer Casting Stainless steel processing 

  Read more

• 

  Precision machining solution for crankshaft holes

  The machining quality of the crankshaft bore has a major impact on the performance of the engine. Chery Engine Division has continuously researched and continuously improved the finishing plan of the crankshaft hole of cast iron engine cyli....

  TAG: CNC machining Lathe processing Turning Milling machining Material Metal Products Manufacturer Casting Stainless steel processing Rapid prototype Aluminum products 

  Read more

• 

  The cylinder block \ box parts dowel hole machining

  The processing of the positioning pin holes of the cylinder parts such as the cylinder block and the cylinder head has always been a key process. The remarkable feature of the box parts is that the process is complicated, and the processing....

  TAG: CNC machining Lathe processing Turning Milling machining Shaft machining Material Metal Products Manufacturer Casting Stainless steel processing Rapid prototype China Rapid prototype 

  Read more

• 

  Eliminate milling hole deformed bell phenomenon

  During the machining process of engine and transmission parts, current process control measures cannot meet the hole machining requirements. The cause of failure is often caused by some failure modes of the machined hole. The distortion of....

  TAG: CNC machining Lathe processing Turning Milling machining Shaft machining Bolt Screws Fasteners Material Metal Products Manufacturer Casting Stainless steel processing 

  Read more

• 

  Forming process of small blind square holes for milling parts

  When developing the SD-95 type magnetoelectric speed odometer, it encountered a special problem of processing small blind square holes. The parts are shown in Figure 1. When the speed odometer is working, the meter and sensor are connected....

  TAG: CNC machining Lathe processing Turning Milling machining Shaft machining Material Metal Products Manufacturer Casting Stainless steel processing Rapid prototype China Rapid prototype 

  Read more

• 

  Application of Thermal Energy and Electrolysis to Deburring of Parts Cross Holes

  By manually handling the burrs of the hydraulic valve, only the visible burrs on some surfaces can be removed, and the burrs cannot be completely removed. The best way to deburr the hydraulic valve cross hole now is thermal energy and elect....

  TAG: Surface treatment Electroplating Anodizing NC processing Lathe processing Turning Shaft machining Bolt Material Metal Products Manufacturer Metal parts products 

  Read more

• 

  Efficient processing of aluminum engine cylinder bore rough boring, finish boring

  Since the cast iron cylinder liner is pre-cast in the blank. The rough and fine boring of cylinder bore is concentrated in the same process with some hole series processing, which makes it the bottleneck of the processing of all aluminum eng....

  TAG: CNC machining Lathe processing Turning Milling machining Material Metal Products Manufacturer Casting Stainless steel processing Rapid prototype Aluminum products 

  Read more

• 

  Spool hole machining of automotive gearbox

  The processing of the valve block of the automatic transmission valve body of the automobile is the most demanding position in the entire machining process of the box hole. It is used in the processing of aluminum alloy valve bodies with a....

  TAG: CNC machining Lathe processing Turning Milling machining Material Metal Products Manufacturer Casting Stainless steel processing Rapid prototype Aluminum products 

  Read more